Combined scale factor & convergence calculator.

State Plane 1983, State Plane 2022 or UTM. Fill in the point, press Calculate, print the report. Converting coordinates instead? Use ZiaCon.

ZiaCon 1.6.1 · Changelog and test record

Input

Pick the zone, enter the point, then press Calculate or Enter. Fields marked * are required.

Horizontal

Coord type

State Plane 1983 is the system most plats and deeds use. State Plane 2022 is NGS’s replacement on NATRF2022, still in beta. UTM is 6° zones in meters. Pick the one the coordinates were computed in.

Datum

The horizontal datum the coordinates are on. NAD83(2011) is current NGS control and what RTK networks and OPUS give you; the control’s datasheet says which.

Zone

The zone the coordinates were computed in. Each zone is its own projection with its own scale, so a factor is only right for its own zone.

Vertical

Vertical datum

Which height you are giving. A NAVD88 elevation (H) is what a plan shows; an ellipsoid height (h) is what GNSS measures. The elevation factor needs h, so an elevation is turned into h with the geoid height N.

Units format
Units format

Lat / long format

How latitude and longitude are written. Degrees-minutes-seconds can be typed 38 34 45.0, 38°34′45.0″ or N383445.0, the way NGS datasheets print it. West longitudes are negative or start with W.

Coordinate units

The unit for northing, easting and height. Each state’s law names the unit for State Plane 1983; ZiaCon starts on that one and the report says so. The US survey foot was retired at the end of 2022, so SPCS2022 has only meters and international feet.

Point
Given as

Elevation

The height of the ground where distances will be measured. The elevation factor brings ground distances down to the ellipsoid; 100 ft of elevation changes it by about 5 ppm. Without an elevation the report gives the grid scale factor only.

ZiaMap

Geodetic Calculation Sheet

Point name

Northing
—
Easting
—
Latitude
—
Longitude
—
Elevation
—
Convergence angle
—
Grid scale factor
—
Elevation factor
—
Combined scale factor
—
1 / Combined scale factor
—

Powered by ZiaMap · ziamap.com · ZiaCon 1.6.1 · Page 1 of 1

Read before you rely on a factor

  • Scale factor and convergence come straight from the zone definition. State Plane 1983 and UTM from the EPSG registry through PROJ, on the GRS 80 ellipsoid; the same engine as ZiaCon, so the two never disagree.
  • State Plane 2022 is NGS beta. The zones come from the NGS SPCS2022 zone definitions, and the report names the revision it used. Every zone is checked against the example point NGS publishes for it. NGS expects to adopt the modernized NSRS in late 2026 to 2027, and zones may change before then. SPCS2022 coordinates are in NATRF2022, not NAD83, and come in meters or international feet only.
  • The elevation factor needs ellipsoid height. A NAVD88 elevation is turned into one with the geoid height N from NGS GEOID18, or GEOID12B in Alaska, Hawaii and the Pacific territories (h = H + N), fetched when you calculate, or typed in yourself.
  • NAD27 is not offered. NAD27 State Plane uses different zone constants on a different ellipsoid, and this tool carries the NAD83 and 2022 ones only.
  • A point outside the chosen zone is refused, the same as in the Converter. No factor is shown for it, on screen or on the report; pick the zone the point is in.
  • This is a field and office convenience tool. Check a known control point before you rely on it. It is not a substitute for the scale factor shown on your recorded survey.
  • Your coordinates stay in your browser. What leaves is the point itself: its county is looked up at the FCC to name a State Plane 1983 zone, its geoid height comes from the NOAA National Geodetic Survey, and the map tiles come from USGS The National Map. None of these agencies produced this tool or endorse it.

Questions surveyors ask about ZiaCon

What is a combined scale factor?

The number that turns a ground distance into a grid distance. It is the grid scale factor, which comes from the zone's projection at the point, times the elevation factor, which allows for the point's height above the ellipsoid. Multiply a ground distance by it to get grid, or divide a grid distance by it to get ground. ZiaCon also gives the convergence angle, the difference between grid north and geodetic north at the point.

Why does the elevation factor need an ellipsoid height?

The elevation factor scales a distance from the ground down to the ellipsoid, so it needs the height above the ellipsoid (h), not the elevation on a plan (H). ZiaCon turns a NAVD 88 elevation into h with NGS's geoid height N (h = H + N), from GEOID18, or GEOID12B in Alaska, Hawaii and the Pacific territories. You can also type h in.

How accurate is ZiaCon?

In a November 2026 test set by Brian Jaquess, PLS, sample points from every state went through ZiaCon and NCAT side by side. In the 49 states whose files were labelled correctly, all 980 points agreed to within 0.17 mm, and the grid scale factor and convergence were identical. Every release also reruns checks against NCAT, NGS datasheets, NGS's State Plane 2022 examples and each state's zone law: ZiaCon 1.6.1 passed 32,421 and failed 0. The changelog lists every check.

Which coordinate systems and datums does ZiaCon handle?

State Plane 1983 for all 50 states, DC and Puerto Rico; State Plane 2022, which NGS has not finalized yet; UTM; and latitude/longitude. Horizontal datums are NAD83 realizations, including NAD83(2011) and, in Hawaii, NAD83(PA11). Heights are NAVD 88 elevations or ellipsoid heights, and Hawaii elevations are local mean sea level.

Every check behind these answers, and what changed in each version: ZiaCon changelog and test record. Converting coordinates? Open ZiaCon.

ZiaCon 1.6.1 · Changelog and test record